MIL-M-38510-245 Microcircuits, Digital, Cmos, 4096 Bit, Static Random Access Memory Sram, Bulk Silicon And Silicon On SapphireThis specification covers the detail requirements for bulk silicon and silicon on sapphire SOS, static, 4096 bit, random access memory microcircuits. Two product assurance classes, four radiation hardness assurance levels, and a choice of case outlines and lead finishes are provided and are reflected in the part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, see 6.4

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73 - 74 - 75 - 76 - 77 - 78

MIL-M-38510/245B

TABLE VII Bias during exposure to radiation.

Device type	Pin connections	VSS = GND	VDD = 5 V dc
Device type	VDD (through a 1 kn to 60 kn resistor)	VSS = GND	VDD = 5 V dc
03	1, 2, 3, 4, 5, 6, 7*, 8, 10, 11, 12, 13, 14, 15, 16, 17	9	18
04	1, 2, 3, 4, 5, 6, 7, 8, 10, 11, 12, 13, 14, 15, 16, 17	9	18
05	1, 2, 3, 4, 5, 6, 7, 8, 10, 11, 12, 13, 14, 15, 16, 17	9	18
06	1, 2, 3, 4, 5, 6, 7, 8, 10, 11, 12, 13, 14, 15, 16, 17	9	18

* Output pins connected to voltage divider.

NOTES

(This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.)

6.1 Intended use. Microcircuits conforming to this specification are intended for logistic support of existing equipment.

6.2 Acquisition requirements. Acquisition documents should specify the following:

a. Title, number, and date of the specification.

b. PIN and compliance identifier, if applicable (see 1.2).

c. Requirements for delivery of one copy of the conformance inspection data pertinent to the device inspection lot to be supplied with each shipment by the device manufacturer, if applicable.

d. Requirements for certificate of compliance, if applicable.

e. Requirements for notification of change of product or process to contracting activity in addition to notification to the qualifying activity, if applicable.

f. Requirements for failure analysis (including required test condition of method 5003 of MIL-STD-883), corrective action, and reporting of results, if applicable.

g. Requirements for product assurance options.

h. Requirements for special carriers, lead lengths, or lead forming, if applicable. These requirements shall not affect the part number. Unless otherwise specified, these requirements will not apply to direct purchase by or direct shipment to the Government.