MIL-M-38510-103 Microcircuits, Linear, Voltage Comparators, Monolithic SiliconThis specification covers the detail requirements for monolithic silicon, voltage comparators. Two product assurance classes and a choice of case outlines and lead finish are provided for each type and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, see 6.3.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73

MIL-M-38510/103H

6.4  Qualification.  With respect to products requiring qualification, awards will be made only for products which are, at the time of award of contract, qualified for inclusion in Qualified Manufacturers List QML-38535 whether or not such products have actually been so listed by that date.  The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they may be eligible to be awarded contracts or purchase orders for the products covered by this specification.  Information pertaining to qualification of products may be obtained from DSCC-VQ, 3990 E. Broad Street, Columbus, Ohio 43128-3990.

6.5   Abbreviations, symbols, and definitions.  The abbreviations, symbols, and definitions used herein are defined in

MIL-PRF-38535, MIL-STD-1331 and as follows:

6.5.1   Logic threshold voltage.  The approximate voltage at the output of the comparator at which the loading logic circuitry changes its digital state.

6.5.2   Voltage gain.  The ratio of the change in output voltage to the change in voltage between the input terminals producing it with the dc output level in the vicinity of the logic threshold voltage (AV).

6.5.3   Response time.  The interval between the application of an input step function and the time when the output crosses the logic threshold voltage.  The input step drives the comparator from some initial, saturated input voltage to an input level just barely in excess of that required to bring the output from saturation to the logic threshold voltage. This excess is referred to as the voltage overdrive.

6.5.4   Positive output level.  The dc output voltage in the positive direction with the input voltage equal to or greater than a minimum specified amount.

6.5.5   Negative output level.  The dc output voltage in the negative direction with the input voltage equal to or greater than a minimum specified amount.

6.5.6   Output sink current.  The maximum negative current that can be delivered by the comparator (IOL).

6.5.7   Peak output current.  The maximum current that may flow into the output load without causing damage to the comparator.

6.5.8   Differential input voltage.  The difference between the two voltages applied to the input terminals of an

amplifier.  The difference is considered positive when the noninverting input is positive with respect to the inverting input and negative when the inverting input is positive with respect to the noninverting input (VID).

6.5.9   Strobe current.  The current into the strobe terminal of an amplifier (ISTB).

6.5.10    Output leakage current.  The current into the output of an amplifier with the output at high level (IO).

6.5.11    Ground leakage current.  The current into the ground terminal of an amplifier with the output at high level (IG).

6.5.12    Input leakage current.  The current into the input terminal of an amplifier with the output at a specified voltage (II).

72