MIL-M-38510-107 Microcircuits, Linear, Positive, Voltage Regulators, Monolithic SiliconThis specification covers the detail requirements for fixed output, monolithic silicon, positive voltage regulators. Two product assurance classes and a choice of case outlines and lead finish are provided for each type and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, see 6.3.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73 - 74 - 75 - 76 - 77 - 78

MIL-M-38510/1070

3.4  Lead material and finish.  Lead material and finish shall be in accordance with MIL-PRF-38535 or as follows: Type X

Nickel  ...............................................................  50-53 percent Manganese  ......................................................  0.60 percent, maximum Silicon  ..............................................................  0.30 percent, maximum Carbon  .............................................................  0.10 percent, maximum Chromium .........................................................  0.25 percent, maximum Cobalt ...............................................................  0.50 percent, maximum Phosphorous ....................................................  0.025 percent, maximum Sulfur  ...............................................................  0.025 percent, maximum Aluminum  .........................................................  0.10 percent maximum Iron     ...............................................................  Remainder

Type Y

Copper core  .....................................................  24.75 percent, maximum

Clad with Alloy 52 .............................................  75.25 percent, maximum

3.4.1   Lead finish.  The lead finish shall be in accordance with MIL-PRF-38535 (see 6.6).

3.5  Electrical performance characteristics.  Unless otherwise specified, the electrical performance characteristics are as specified in table I and apply over the full operating ambient temperature range of -55°C to +125°C.

3.5.1  Stability.  If the device is located an appreciable distance from the power supply filter, a large (1.0 μF) bypass capacitor should be connected as close to the device VCC input as possible to suppress oscillation.  A 0.1 μF bypass capacitor is

recommended on the device output.  Output current oscillations are likely to occur in the current limit operating mode with high input

voltages (VIN > 18 V dc).

3.5.2  Test limit.  The test limits specified in tables I and III apply only for the stated test conditions (example, 2 percent duty cycle), which essentially keep the junction temperature constant.  In most applications the junction temperature will greatly exceed the 25°C ambient or sink temperature; thus devices may not perform within the 25°C specified limits.

3.6  Electrical test requirements.  Electrical test requirements for each device class shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table III.

3.7  Marking.  Marking shall be in accordance with MIL-PRF-38535.

3.8  Microcircuit group assignment.  The devices covered by this specification shall be in microcircuit group number 52 (see MIL-PRF-38535, appendix A).

4