MIL-M-38510-107 Microcircuits, Linear, Positive, Voltage Regulators, Monolithic SiliconThis specification covers the detail requirements for fixed output, monolithic silicon, positive voltage regulators. Two product assurance classes and a choice of case outlines and lead finish are provided for each type and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, see 6.3.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73 - 74 - 75 - 76 - 77 - 78

INCH-POUND MIL-M-38510/107D

24 February 2004

SUPERSEDING MIL-M-38510/107C

29 May 1989

MILITARy SPECIFICATION

MICROCIRCUITS, LINEAR, POSITIVE, VOLTAGE REGULATORS, MONOLITHIC SILICON

This specification is approved for use by all Departments and Agencies of the Department of Defense. Reactivated after 24 February 2004 and may be used for either new or existing design acquisition.

The requirement for acquiring the product herein shall consist of this specification sheet and MIL-PRF-38535.

1. SCOPE

1.1 Scope. This specification covers the detail requirements for fixed output, monolithic silicon, positive voltage regulators. Two product assurance classes and a choice of case outlines and lead finish are provided for each type and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, (see 6.3).

1.2 Part or Identifying Number (PIN). The PIN is in accordance with MIL-PRF-38535, and as specified herein.

1.2.1 Device types. The device types are as shown in the following:

Device type Circuit Case outline letter

01	Voltage regulator, +5 volts at 1.5 A (maximum)	x or y (see table I)
02	Voltage regulator, +5 volts at 0.5 A	x
03	Voltage regulator, +12 volts at 0.5 A	x
04	Voltage regulator, +15 volts at 0.5 A	x
05	Voltage regulator, +24 volts at 0.5 A	x
06	Voltage regulator, +5 volts at 1.0 A	y
07	Voltage regulator, +12 volts at 1.0 A	y
08	Voltage regulator, +15 volts at 1.0 A	y
09	Voltage regulator, +24 volts at 1.0 A	y

1.2.2 Device class. The device class is the product assurance level as defined in MIL-PRF-38535.

1.2.3 Case outlines. The case outlines should be designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style

x	See figure 1	3	Can
y	See figure 2	2	Flange mount

Comments, suggestions, or questions on this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAS, 3990 East Broad St., Columbus, OH 43216-5000, or emailed to linear@dscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at www.dodssp.daps.mil.

AMSC N/A FSC 5962