MIL-M-38510-206 Microcircuit, Digital, 4096 Bit Schottky, Bipolar, Programmable Read-Only Memory PromThis specification covers the detail requirements for monolithic silicon, programmable read-only memory PROM microcircuits which employ thin film nichrome NiCr resistors, tungsten W or titanium tungsten TiW as the fusible link or programming element. Two product assurance classes and a choice of case outlines and lead finishes are provided and are reflected in the complete part number. A special test requirement is included in this specification to screen against devices which may contain excess moisture in the package materials or internal atmosphere see freeze-out test of 4.2d. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, see 6.4.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41

MIL-M-38510/206D

4.4  Technology Conformance inspection (TCI).   Technology conformance inspection shall be in accordance with MIL-PRF-38535 and as specified herein for groups A, B, C, and D inspections (see 4.4.1 through 4.4.4).

4.4.1  Group A inspection.  Group A inspection shall be in accordance with table III of MIL-PRF-38535 and as follows:

a.  Electrical test requirements shall be as specified in table II herein. b.  Subgroups 4, 5, and 6 shall be omitted.

c.  For unprogrammed devices, a sample shall be be selected to satisfy programmability requirements prior to performing subgroups 9. 10, and 11.  Twelve devices shall be submitted to programming (see

3.3.2.1).  If more than 2 devices fail to program, the lot shall be rejected,  At the manufacturer's option, the sample may be increased to 24 total devices with no more thatn 4 total device failures

allowable.

d.  For unprogrammed devices, 10 devices from the programmability sample shall be submitted to the requirements of group A, subgroups 9, 10, and 11.  If more than two total devices fail in all three subgroups, the lot shall be rejected.  At the manufacturer's option, the sample may be increased to 20 total devices with no more that 4 total device failures allowable.

4.4.2  Group B inspection.  Group B inspection shall be in accordance with table II MIL-PRF-38535. (a)   Electrical test requirements shall be as specified in table II herein.

(b)   For qualification, at least 50 percent of the sample selected for testing in subgroup 5 shall be programmed (see 3.3.2).  For quality conformance inspection, the programmability sample (see

4.4.1c) shall be included in the subgroup 5 tests.

4.4.3  Group C inspection.  Group C inspection shall be in accordance with table IV of MIL-PRF-38535 and as follows:

a.  End-point electrical parameters shall be as specified in table II herein.

b.  The steady-state life test duration, test condition, and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535.  The burn- in test circuit shall be maintained under document control by the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request.  The test circuit shall specify the inputs, outputs, biases, and

power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL- STD-883.

c.  For qualification, at least 50 percent of the sample selected for testing in subgroup 1 shall be programmed (see 3.3.2).  For quality conformance inspection, the programmability sample (see

4.4.1c) shall be included in the subgroup 1 tests.

4.4.4  Group D inspection.  Group D inspection shall be in accordance with table V of MIL-PRF-38535.  End- point electrical parameters shall be as specified in table II herein.

4.5  Methods of inspection.  Methods of inspection shall be specified and as follows:

4.5.1  Voltage and current.  All voltages given are referenced to the microcircuit ground terminal.  Currents given are conventional and positive when flowing into the referenced terminal.

4.6     Programming procedure identification.   The programming procedure to be utilized shall be identified by the manufacturer's circuit designator.

23