TABLE III. Group A inspection for device type 06 - Continued. 11
Subgroup |
Symbol |
MIL- STD-883 method |
Cases A,B,D |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
Measured terminal |
Limits |
Unit |
|
Case C |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
Min |
Max |
|||||
Test no. |
Clock 1 |
Clear 1 |
K1 |
VCC |
Clock 2 |
Clear 2 |
J2 |
Q2 |
Q2 |
K2 |
GND |
Q1 |
Q1 |
J1 |
|||||||
10 TC=+125°C |
fMAX 61 |
(Fig. 15) |
82 83 84 85 |
IN IN |
5.0 V 5.0 V |
2.4 V 2.4 V |
5.0 V " " " |
IN IN |
5.0 V 5.0 V |
2.4 V 2.4 V |
OUT |
OUT |
2.4 V 2.4 V |
GND " " " |
OUT |
OUT |
2.4 V 2.4 V |
Q1 Q1 Q2 Q2 |
30 " " " |
MHz " " " |
|
tPLH1 |
3003 (Fig. 14) |
86 87 |
G |
IN |
2.4 V |
" " |
G |
IN |
2.4 V |
OUT |
2.4 V |
" " |
OUT |
2.4 V |
Clear 1 to Q Clear 2 to Q |
2 " |
18 18 |
ns " |
|||
tPHL1 |
88 89 90 91 |
F G |
IN IN |
2.4 V 2.4 V |
" " " " |
F G |
IN IN |
2.4 V 2.4 V |
OUT OUT |
2.4 V 2.4 V |
" " " " |
OUT OUT |
2.4 V 2.4 V |
Clear 1 to Q Clear 2 to Q Clock 1 to Q Clock 2 to Q |
" " " " |
46 46 28 28 |
" " " " |
||||
tPLH2 |
3003 (Fig. 15) |
92 93 94 95 |
IN IN |
2.4 V P |
" " " " |
IN IN |
N 2.4 V |
OUT |
OUT |
2.4 V P |
" " " " |
OUT |
OUT |
N 2.4 V |
Clock 1 to Q Clock 1 to Q Clock 2 to Q Clock 2 to Q |
" " " " |
23 " " " |
" " " " |
|||
tPHL2 |
96 97 98 99 |
IN IN |
R 2.4 V |
" " " " |
IN IN |
2.4 V S |
OUT |
OUT |
R 2.4 V |
" " " " |
OUT |
OUT |
2.4 V S |
Clock 1 to Q Clock 1 to Q Clock 2 to Q Clock 2 to Q |
" " " " |
28 " " " |
" " " " |
||||
11 |
Same tests, terminal conditions, and limits as subgroup 10, except TC = -55°C. |
||||||||||||||||||||
A = Normal clock pulse.
D = Momentary 4.5 V, then GND.
F = Momentary 0 V, then Vgen, see figure 14. G = Momentary Vgen, then 0 V, see figure 14.
N = tsetup waveform, see figure 15. P = tsetup waveform, see figure 15. R = tsetup waveform, see figure 15. S = tsetup waveform, see figure 15.
* = Duration of test should not exceed 1 second.
** = Limit duration of this test to 100 ns.
11 Terminal conditions (pins not designated may be H � 2.0 V, or L ≤ 0.8 V, or open).
21 Input shall be 4.5 V with a momentary ground, then 4.5 V 4.5 V .
0 V
31 Tests shall be performed in sequence.
41 Input voltages shown are: A = 2.0 volts minimum and B = 0.8 volts maximum.
51 Output voltages shall be either: a. H = 2.4 V, minimum and L = 0.4 V, maximum when using a high speed checker double comparator; or b. H � 1.5 V and L ≤ 1.5 V when using a high speed checker single comparator.
61 fMAX, minimum limit specified is the frequency of the input pulse. The output frequency shall be one-half of the input frequency.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business