An Integrated Publishing, Inc. Site

An Integrated Publishing Website

MIL-M-38510-13 Microcircuits, Digital, Bipolar, Ttl, Counters Monolithic SiliconThis specification covers the detail requirements for monolithic silicon, TTL, binary and decade counters. Two product assurance classes and a choice of case outlines and lead finishes are provided for each type and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535, see 6.4.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73 - 74 - 75 - 76 - 77 - 78 - 79 - 80 - 81 - 82 - 83 - 84 - 85 - 86 - 87 - 88 - 89 - 90 - 91

TABLE III. Group A inspection for device type 06 - Continued.

Terminal conditions 2/

Subgroup

Symbol

MIL- STD-883 method

Case E, F

Meas. terminal

Test limits

Test No.

Clear

Clock

DATA INPUTS

Enable

GND

Load

Enable

Output

Carry output

VCC

Min

Max

Unit

TC =125°C

tPLH4 tPLH4 tPLH4 tPLH4 tPLH5 tPHL5 tPHL6 tPHL6 tPHL6

tPHL6

Fig 7 and 7A "

" " " " " "

195

196

197

198

199

200

201

202

203

204

8/ "

" "

4.5 V

4.5 V IN

" "

IN "

" "

7/ IN "

4.5 V "

" " " " " "

4.5 V IN

4.5 V "

" " " " "

4.5 V

4.5 V IN

4.5 V "

" " " "

4.5 V

4.5 V IN

4.5 V "

" " "

4.5 V "

" " " " " " "

GND "

" " " " " " "

GND "

" " " " " " "

4.5 V "

" " IN IN

4.5 V "

OUT

OUT OUT

5.0 V "

" " " " " " "

QA QB QC QD

Carry

QA QB QC QD

3 " " " " " " " "

36 "

" "

47 "

" " " " " " " " "

Same tests, terminal conditions and limits as subgroup 10, except TC = -55°C.

1/ Normal clock pulse: (VIL < 0.8 V, VIH > 2.0 V).

2/ Terminal conditions (pins not designated may be H > 2.0 V, or L < 0.8 V, or open).

3/ Output voltages shall be either:

(a) H = 2.4 volts minimum and L = 0.4 volt maximum when using a high speed checker double comparator, or

(b) H > 1.5 volts and L < 1.5 volts when using a high speed checker single comparator.

4/ Only a summary of attributes data is required.

5/ A > 2.0 V, B < 0.8 V. Input voltages shown are the maximum for VIL and the minimum for VIH.

6/ FMAX, minimum limit specified is the frequency of the input pulse. The output frequency shall be as follows: FMAX/2 at QA, FMAX/4 at QB,

FMAX/8 at QC, FMAX/16 at QD.

7/ Apply 1 clock pulse prior to input pulses.

8/ Apply momentarily GND, then 4.5 volts prior to input pulses, maintain 4.5 volts during test.

9/ Minimum limit for circuit C shall be -0.5 mA.