TA8LE III. Group A inspection for device type 53 - Continued.
Symbol |
MIL- STD- 883 method |
Cases 2,R |
Terminal conditions 11 |
Measured terminal |
Test limits |
Unit |
||||||||||||||||||||||||
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
15 |
16 |
17 |
18 |
19 |
20 |
Subgroup 9 TC = +25°C 41 |
Subgroup 10 TC = +125°C |
Subgroup 11 TC = -55°C 41 |
||||||||
Test no. |
DIR |
A1 |
A2 |
A3 |
A4 |
A5 |
A6 |
A7 |
A8 |
GND |
88 |
87 |
86 |
85 |
84 |
83 |
82 |
81 |
G |
VCC |
Min |
Max |
Min |
Max |
Min |
Max |
||||
tPZL1 |
3003 (Fig. 3) |
282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 |
GND " " " " " " " 4.5V " " " " " " " |
OUT GND |
OUT GND |
OUT GND |
OUT GND |
OUT GND |
OUT GND |
OUT GND |
OUT GND |
GND " " " " " " " " " " " " " " " |
GND OUT |
GND OUT |
GND OUT |
GND OUT |
GND OUT |
GND OUT |
GND OUT |
GND OUT |
IN " " " " " " " " " " " " " " " |
4.5V " " " " " " " " " " " " " " " |
G to A1 G to A2 G to A3 G to A4 G to A5 G to A6 G to A7 G to A8 G to 81 G to 82 G to 83 G to 84 G to 85 G to 86 G to 87 G to 88 |
6 " " " " " " " " " " " " " " " |
41 " " " " " " " " " " " " " " " |
6 " " " " " " " " " " " " " " " |
54 " " " " " " " " " " " " " " " |
6 " " " " " " " " " " " " " " " |
41 " " " " " " " " " " " " " " " |
ns " " " " " " " " " " " " " " " |
tPLZ1 |
3003 (Fig. 3) |
298 to 313 |
Same terminal conditions and measured terminals as specified above for tPZL1. |
" |
" |
" |
" |
" |
" |
" |
||||||||||||||||||||
11 Pins not designated may be "High" level logic, "Low" level logic, or open. Exceptions are as follows:
a. VIC(pos) tests, the GND terminal shall be open. A minimum limit of 0.4 V applies to tests being performed on equipment not capable of opening the GND pin during testing. b. VIC(neg) tests, the VCC terminal shall be open.
c. ICC tests, the output terminal shall be open.
21 Three-state output conditions are required. For IOZL, set output to high state. For IOZH, set output to low state. Set input pins to
VIL = VIL(max) or to VIH = VIH(min), as required for each test.
31 See 4.4.1c.
41 See 4.4.1d.
51 Tests shall be performed in sequence, attributes data only.
61 H > 1.5V; L < 1.5V; A = 0.7V; 8 = 0.4V; for the device type 53 A = 2.4V; 8 = 0.4V.
71 Three-state output conditions are required.
81 fMAX minimum limit specified is the frequency of the input pulse. The output frequency shall be one-half of the input frequency. The fMAX requirement is considered met if proper output state changes occur with the pulse repetition period set to that given in the limits columns.
91 Add 1 kO minimum resistor between VCC and output to pull output to high state.
101 Add 1 kO minimum resistor between GND and output to pull output to low state.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business