TABLE III. Group A inspection for device type 53 - Continued.
Symbol |
MIL- STD- 883 method |
Case |
Terminal conditions 1/ |
Measured terminal |
Test limits |
Unit |
||||||||||||||||||||
2 |
2 |
3 |
4 |
5 |
7 |
8 |
9 |
10 |
12 |
13 |
14 |
15 |
17 |
18 |
19 |
20 |
Subgroup 9 TC = +25°C 5/ |
Subgroup 10 TC = +125°C |
Subgroup 11 TC = -55°C 5/ |
|||||||
E and F |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
15 |
16 |
||||||||||
Test no. |
G1 |
A1 |
B1 |
1Y0 |
1Y1 |
1Y2 |
1Y3 |
GND |
2Y3 |
2Y2 |
2Y1 |
2Y0 |
B2 |
A2 |
G2 |
VCC |
Min |
Max |
Min |
Max |
Min |
Max |
||||
tTHL |
3003 (Fig. 4) |
130 131 132 133 134 135 136 137 |
IN " " " GND " " " |
GND 4.5V GND 4.5V GND " " " |
GND GND 4.5V 4.5V GND " " " |
GND " " " " " " " |
GND " " " " " 4.5V 4.5V |
GND " " " " 4.5V GND 4.5V |
GND " " " IN " " " |
4.5V " " " " " " " |
1Y0 1Y1 1Y2 1Y3 2Y0 2Y1 2Y2 2Y3 |
3 " " " " " " " |
15 " " " " " " " |
3 " " " " " " " |
20 " " " " " " " |
3 " " " " " " " |
15 " " " " " " " |
ns " " " " " " " |
||||||||
tTLH |
3003 (Fig. 4) |
138 139 140 141 142 143 144 145 |
IN " " " GND " " " |
" 4.5V GND 4.5V GND " " " |
" " 4.5V 4.5V GND " " " |
" " " " " " " " |
GND " " " " " 4.5V 4.5V |
GND " " " " 4.5V GND 4.5V |
GND " " " IN " " " |
" " " " " " " " |
1Y0 1Y1 1Y2 1Y3 2Y0 2Y1 2Y2 2Y3 |
" " " " " " " " |
" " " " " " " " |
" " " " " " " " |
" " " " " " " " |
" " " " " " " " |
" " " " " " " " |
" " " " " " " " |
||||||||
1/ Output pins not designated may be high level logic, low level logic, open. Input pins not designated may be high level logic or low level logic.
Exceptions are as follows:
a. VIC(pos) tests, the GND terminal shall be open. A minimum limit of 0.4 V applies to tests being performed on equipment not capable of opening the GND pin during test.
b. VIC(neg) tests, the VCC terminal shall be open. c. ICC tests, the output terminal shall be open.
2/ See 4.4.1c.
3/ Tests shall be performed in sequence. A = 2.4 V; B = 0.4 V for device types 52 and 53; A = 3.7 V; B = 0.4 V for device types 01 through 04.
4/ X = indeterminate output voltage. Output shall be H > 2.5 V; L < 2.5 V.
5/ See 4.4.1d.
6/ The input signal for HCT device types shall be 0 to 3 volts; however, the 50 percent VCC measuring point is 1.3 V for input and output signals.
The 10 percent and 90 percent VCC points are 0.3 V and 2.7 V, respectively for HCT devices.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business