TABLE III. Group A inspection for all device type 08.
Subgroup |
Symbol |
Test no. |
Measurement value |
Adapter pin number see figure 6 |
Pin measurement |
Equation |
Limits |
Unit |
||
1 |
2 |
Min |
Max |
|||||||
1 TA = +25°C |
ICC |
1 |
I1 |
12 V |
0 mA |
1 |
ICC = I1 |
--- |
1.2 |
mA |
VO 11 |
2 |
V1 |
12 V |
0 mA |
2 |
VO = V1 |
6.950 |
7.050 |
V |
|
VRLINE 21 |
3 4 |
V2 V3 |
8.5 V 40 V |
0 mA 0 mA |
2 2 |
VRLINE = V1 - V2 VRLINE = V1 - V3 |
-0.1 -0.39 |
0.1 0.39 |
mV mV |
|
VRLOAD 21 |
5 6 |
V4 V5 |
12 V 12 V |
0 mA -10 mA |
2 2 |
VRLOAD = V4 - V5 |
-1.75 |
1.75 |
mV |
|
IMIN |
7 8 |
V6 I2 |
0 mA 0 mA |
2 mA V7 |
2 2 |
V7 = V6 - 50 mV IMIN = I2 |
--- |
--- 1 |
mA |
|
VSHUNT 21 31 |
9 10 |
V8 V9 |
0 mA 0 mA |
1.2 mA 10 mA |
2 2 |
VSHUNT = V9 - V8 |
-6.16 |
6.16 |
mV |
|
IOS |
11 |
I3 |
12 V |
0 V |
2 |
IOS = I3 |
-50 |
--- |
mA |
|
2 TA = +125°C |
ICC |
12 |
I4 |
12 V |
0 mA |
1 |
ICC = I4 |
--- |
1.5 |
mA |
VO 11 |
13 |
V10 |
12 V |
0 mA |
2 |
VO = V10 |
6.9465 |
7.0535 |
V |
|
VRLINE 21 |
14 15 |
V11 V12 |
8.5 V 40 V |
0 mA 0 mA |
2 2 |
VRLINE = V10 - V11 VRLINE = V10 - V12 |
-0.2 -0.78 |
0.2 0.78 |
mV mV |
|
VRLOAD 21 |
16 17 |
V13 V14 |
12 V 12 V |
0 mA -10 mA |
2 2 |
VRLOAD = V13 - V14 |
-2.8 |
2.8 |
mV |
|
IMIN |
18 19 |
V15 I5 |
0 mA 0 mA |
2 mA V16 |
2 2 |
V16 = V15 - 50 mV IMIN = I5 |
--- |
--- 1.2 |
mA |
|
VSHUNT 21 31 |
20 21 |
V17 V18 |
0 mA 0 mA |
1.2 mA 10 mA |
2 2 |
VSHUNT = V18 - V17 |
-9.24 |
9.24 |
mV |
|
?VO 1 ?T |
22 |
?VO 1 ?T = (V10 - V1) 1100 |
--- |
5 |
ppm1°C |
|||||
3 TA = -55°C |
ICC |
23 |
I6 |
12 V |
0 mA |
1 |
ICC = I6 |
--- |
1.5 |
mA |
VO 11 |
24 |
V19 |
12 V |
0 mA |
2 |
VO = V19 |
6.9472 |
7.0528 |
V |
|
VRLINE 21 |
25 26 |
V20 V21 |
8.5 V 40 V |
0 mA 0 mA |
2 2 |
VRLINE = V19 - V20 VRLINE = V19 - V21 |
-0.2 -0.78 |
0.2 0.78 |
mV mV |
|
VRLOAD 21 |
27 28 |
V22 V23 |
12 V 12 V |
0 mA -10 mA |
2 2 |
VRLOAD = V22 - V23 |
-2.8 |
2.8 |
mV |
|
IMIN |
29 30 |
V24 I7 |
0 mA 0 mA |
2 mA V25 |
2 2 |
V25 = V24 - 50 mV IMIN = I7 |
--- |
--- 1.2 |
mA |
|
VSHUNT 21 31 |
31 32 |
V26 V27 |
0 mA 0 mA |
1.2 mA 10 mA |
2 2 |
VSHUNT = V27 - V26 |
-9.24 |
9.24 |
mV |
|
?VO 1 ?T |
33 |
?VO 1 ?T = (V19 - V1) 180 |
--- |
5 |
ppm1°C |
|||||
4 TA = +25°C |
NO 41 |
34 |
N1 |
15 V |
0 mA |
--- |
See figure 7 |
--- |
4 |
∝V RMS |
11 Reference voltage is measured immediately after device is turned ON. Changes due to chip warm up are typically less that 0.005 percent.
21 Line, load, and shunt mode regulation are measured on a pulse basis. Pulse is not to exceed 30 ms.
31 Shunt voltage is measured with the input open. With the input connected, the shunt mode current can be reduced to 0 mA. Load regulation will remain the same.
41 RMS noise is measured with a two pole high pass filter at 10 Hz and a two pole low pass filter at 1 kHz.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business