INCH-POUND MIL-M-38510/50F
20 October 2004
MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, CMOS, NAND GATES, MONOLITHIC SILICON, POSITIVE LOGIC
SUPERSEDING MIL-M-38510/50E
30 April 1984
Reactivated after 20 October 2004 and may be used for new and existing designs and acquisitions.
This specification is approved for use by all Departments and Agencies of the Department of Defense.
The requirements for acquiring the product herein shall consist of this specification sheet and MIL-PRF 38535
1. SCOPE
1.1 Scope. This specification covers the detail requirements for monolithic silicon, CMOS, logic microcircuits.
Two product assurance classes and a choice of case outlines, lead finishes, and radiation hardness assurance (RHA) are provided and are reflected in the complete Part or Identifying Number (PIN). For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535 (see 6.3).
1.2 Part or identifying number (PIN). The PIN is in accordance with MIL-PRF-38535 and as specified herein.
1.2.1 Device types. The device types are as follows: Device type Circuit
01 Quadruple 2-input NAND gate
02 Dual 4-input NAND gate
03 Triple 3-input NAND gate
51 Quadruple 2-input NAND gate
52 Dual 4-input NAND gate
53 Triple 3-input NAND gate
1.2.2 Device class. The device class is the product assurance level as defined in MIL-PRF-38535.
1.2.3 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter A |
Descriptive designator GDFP5-F14 or CDFP6-F14 |
Terminals 14 |
Package style Flat pack |
C |
GDIP1-T14 or CDIP2-T14 |
14 |
Dual-in-line |
D |
GDFP1-F14 or CDFP2-F14 |
14 |
Flat pack |
T |
CDFP3-F14 |
14 |
Flat pack |
X 1/ 2/ |
GDFP5-F14 or CDFP6-F14 |
14 |
Flat pack, except A dimension |
equals 0.1" (2.54 mm) max |
|||
Y 1/ 2/ |
GDFP1-F14 or CDFP2-F14 |
14 |
Flat pack, except A dimension |
equals 0.1" (2.54 mm) max |
1/ As an exception to MIL-PRF-38535, appendix A, for case outlines X and Y only, the leads of bottom brazed ceramic packages (i.e., configuration 2 of case outlines A or D) may have electroless nickel undercoating which is 50 to 200 microinches (1.27 to 5.08 ยตm) thick provided the lead finish is hot solder dip (i.e., finish
letter A) and provided that, after any lead forming, an additional hot solder dip coating is applied which extends
from the outer tip of the lead to no more than 0.015 inch (0.38 mm) from the package edge.
2/ For bottom or side brazed packages, case outlines X and Y only, the S1 dimension may go to .000 inch
(.00 mm) minimum.
Comments, suggestions, or questions on this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAC, P.O. Box 3990, Columbus, OH 43218-3990, or email CMOS@dscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https://www.dodssp.daps.mil.
AMSC N/A FSC 5962
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business