TA8LE III. Group A inspection for device types 01 - Continued.
Terminal conditions (outputs not designated are open or resistive, coupled to GND or voltage; Inputs not designed are high � 2.0 V, low s 0.8 V or open).
Subgroup |
Symbol |
MIL- STD- 883 method |
Cases J,K,L |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
15 |
16 |
17 |
18 |
19 |
20 |
21 |
22 |
23 |
24 |
Measured terminal |
Test limits |
Unit |
|
Test no. |
NC |
NC |
A0 |
A1 |
A2 |
E1 |
E2 |
A3 |
A4 |
A5 |
G1 |
H |
G2 |
F |
87 |
86 |
85 |
84 |
83 |
82 |
81 |
80 |
G'2 |
VCC |
Min |
Max |
|||||
8 TC = 125°C and -55°C |
Truth table test |
122- 185 |
Repeat subgroup 7, except TC = +125°C. |
||||||||||||||||||||||||||||
186- 249 |
Repeat subgroup 7, except TC = -55°C. |
||||||||||||||||||||||||||||||
9 TC = 25°C |
tPHL and tPLH |
3003 (Fig. 5) " " " " " " " " " " " " " " |
250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 |
5/ " " " " " " " " " " " " " " " |
5/ " " " " " " " " " " " " " " " |
5/ " " " " " " " " " " " " " " " |
5.0V " " " " " " " IN " " " " " " " |
IN " " " " " " " 5.0V " " " " " " " |
5/ " " " " " " " " " " " " " " " |
5/ " " " " " " " " " " " " " " " |
5/ " " " " " " " " " " " " " " " |
GND " " " " " " " " " " " " " " " |
GND " " " " " " " " " " " " " " " |
OUT OUT |
OUT OUT |
OUT OUT |
OUT OUT |
OUT OUT |
OUT OUT |
OUT OUT |
OUT OUT |
GND " " " " " " " " " " " " " " " |
5.0V " " " " " " " " " " " " " " " |
80 81 82 83 84 85 86 87 80 81 82 83 84 85 86 87 |
25 " " " " " " " " " " " " " " " |
85 " " " " " " " " " " " " " " " |
ns " " " " " " " " " " " " " " " |
||||
10 |
Same tests and terminal conditions as for subgroup 9, except TC = 125°C and the limits are 25 ns minimum and 140 ns maximum. |
||||||||||||||||||||||||||||||
11 |
Same tests, terminal conditions, and limits as for subgroup 10, except TC = -55°C. |
||||||||||||||||||||||||||||||
1/ Unprogrammed device conditions.
2/ VOL = 0.45 V for circuit A and 0.50 V for circuit 8.
3/ Input voltages shall be: A = 2.0 V minimum; 8 = 0.8 V maximum.
4/ Output voltages shall be either:
a. H = 2.4 V minimum and L = VOL (VOL = 0.45 V maximum for circuit A and 0.50 V maximum for circuit 8) when using a high speed checker double comparator. b. H � 1.0 V and L < 1.0 V when using a high speed checker single comparator.
5/ Terminal conditions (GND or 5.0 V) shall be as specified on figure 5 or in the altered item drawing, as applicable, so that all outputs are at a low logic level.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business