MIL-M-38510-751 Microcircuits, Digital, Advanced Cmos, Nor Gates, Monolithic SiliconThis specification covers the detail requirements for monolithic silicon, advanced CMOS, logic microcircuits. Two product assurance classes and a choice of case outlines, lead finishes, provided and are reflected in the complete Part or Identifying Number PIN. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF-38535 see 6.3.0.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20

MIL-M-38510/751B

1.3 Absolute maximum ratings. 1/ 2/

Supply voltage range (VCC)........................................................................................ -0.5 V dc to +6.0 V dc

DC input voltage range (VIN) ...................................................................................... -0.5 V dc to VCC + 0.5 V dc

DC output voltage range (VOUT) ................................................................................. -0.5 V dc to VCC + 0.5 V dc

Clamp diode current (IIK, IOK) ..................................................................................... ±20 mA

DC output current (IOUT) ............................................................................................. ±50 mA

DC VCC or GND current (ICC, IGND) ............................................................................. ±100 mA

Storage temperature range (TSTG) ............................................................................. -65°C to +150°C Maximum power dissipation (PD) ............................................................................... 500 mW

Lead temperature (soldering, 10 seconds) ................................................................ +300°C

Thermal resistance, junction-to-case (eJC)................................................................. See MIL-STD-1835

Junction temperature (TJ) .......................................................................................... +175°C

Case operating temperature range (TC)..................................................................... -55°C to +125°C

1.4 Recommended operating conditions. 2/ 3/ 4/

Supply voltage range (VCC)........................................................................................ +3.0 V dc to +5.5 V dc Input voltage range (VIN) ............................................................................................ +0.0 V dc to VCC Output voltage range (VOUT)....................................................................................... +0.0 V dc to VCC

Case operating temperature range (TC)..................................................................... -55°C to +125°C

Maximum low level input voltage(VIL) ........................................................................ 0.90 V dc at VCC = 3.0 V dc

1.35 V dc at VCC = 4.5 V dc

1.65 V dc at VCC = 5.5 V dc

Minimum high level input voltage (VIH)....................................................................... 2.10 V dc at VCC = 3.0 V dc

3.15 V dc at VCC = 4.5 V dc

3.85 V dc at VCC = 5.5 V dc

Input rise and fall rate (tr, tf) maximum:

VCC = 3.6 V, VCC = 5.5 V ......................................................................................... 8 ns/V

1.5 Radiation features.

Device type 01:

Maximum total dose (dose rate = 50 - 300 rads (Si)/s) .......................................... 100 krads (Si) Single Event Latch-up (SEL) .................................................................................. � 93 MeV-cm2/mg

1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. The maximum junction temperature may be exceeded for allowable short duration burn-in screening conditions in accordance with MIL-PRF-38535.

2/ Unless otherwise noted, all voltages are referenced to GND.

3/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery back-up systems. Data retention implies no input transitions and no stored data loss with the following conditions: VIH � 70 percent of VCC, VIL ≤ 30 percent of VCC, VOH � 70 percent of VCC at -20 µA, VOL ≤ 30 percent of VCC at 20 µA.

4/ Unless otherwise specified, the values listed above shall apply over the full VCC and TC recommended operating range.