TA8LE lll. Group A inspection for device type 06 - Continued.
Terminal conditions (pins not designated may be high 2.0 V; low σ 0.7 V; or open).
Subgroup |
Symbol |
MlL-STD- 883 method |
Cases E, F |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
15 |
16 |
Measured terminal |
Limits |
Unit |
|
Cases 1/ 2, X |
2 |
3 |
4 |
5 |
7 |
8 |
9 |
10 |
12 |
13 |
14 |
15 |
17 |
18 |
19 |
20 |
|||||||
Test no. |
S |
1A |
18 |
1Y |
2A |
28 |
2Y |
GND |
3Y |
38 |
3A |
4Y |
48 |
4A |
G |
VCC |
Min |
Max |
|||||
9 Tc = 25°C |
tPHZ3 |
3003 Fig. 5 " " |
104 |
5.0 V |
5.0 V |
OUT |
GND |
lN |
" |
G to 1Y |
3 |
35 |
ns |
||||||||||
105 |
" |
5.0 V |
OUT |
" |
" |
" |
G to 2Y |
" |
" |
" |
|||||||||||||
106 |
" |
" |
OUT |
5.0 V |
" |
" |
G to 3Y |
" |
" |
" |
|||||||||||||
107 |
" |
" |
OUT |
5.0 V |
" |
" |
G to 4Y |
" |
" |
" |
|||||||||||||
tPLZ3 |
" " " " |
108 |
GND |
GND |
OUT |
" |
" |
" |
G to 1Y |
" |
30 |
" |
|||||||||||
109 |
" |
GND |
OUT |
" |
" |
" |
G to 2Y |
" |
" |
" |
|||||||||||||
110 |
" |
" |
OUT |
GND |
" |
" |
G to 3Y |
" |
" |
" |
|||||||||||||
111 |
" |
" |
OUT |
GND |
" |
" |
G to 4Y |
" |
" |
" |
|||||||||||||
10 |
Same tests, terminal conditions and limits as subgroup 9, except TC = +125°C and for the following: tPLH1 and tPHL1 = 3 to 35 ns; tPLH5 and tPHL5 = 3 to 39 ns; tPZH3, tPZL3, and tPHZ3 = 3 to 53 ns; tPLZ3 = 3 to 45 ns. |
||||||||||||||||||||||
11 |
Same tests, terminal conditions and limits as subgroup 10, except TC = -55°C. |
||||||||||||||||||||||
1/ Case X and 2 pins not referenced are NC.
2/ llL limits shall be as follows:
Test |
Min/Max limits (mA) for circuits |
||||||
A |
8 |
C |
D |
E |
F |
G |
|
llL1 |
-.15/-.38 |
-.16/-.40 |
-.20/-.44 |
0/-.30 |
0/-.20 |
-.12/-.36 |
0/-.15 |
llL2 test 27 |
0/-.20 |
-.16/-.40 |
-.20/-.44 |
0/-.30 |
0/-.10 |
-.12/-.36 |
0/-.15 |
llL2 test 28 |
0/-.20 |
-.32/-.80 |
-.40/-.88 |
0/-.60 |
0/-.10 |
-.24/-.72 |
0/-.15 |
3/ lOS limits for circuits 8, C, D, F, and G are -15 to -100 mA.
4/ lnputs: A 2.5 V minimum, 8 σ 0.4 V maximum.
Outputs: Output voltages shall be either:
a. H = 2.5 volts minimum and L = 0.4 volt maximum when using a high speed checker double comparator, or b. H 1.5 volts and L σ 1.5 volts when using a high speed checker single comparator.
c. Attributes data only is required for subgroups 7 and 8.
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business